#Ethernet loopback free

Carrier sensing alone, however, provides only a statistical defence against collisions, the reason being that signals take time to propagate throughout the network. That’s the ‘carrier sense’ part of the protocol. Firstly, all nodes continuously monitor the transmission medium for the presence of a signal (carrier), and will only attempt to send data when none is detected. Clearly this state of affairs has serious implications for the efficiency of a network.ĬSMA/CD seeks to mitigate the problem in two ways. The only recourse is to try again (which again entails the risk of failure). Since collisions effectively randomise the electrical state of the wire, all such transmissions are void.

#Ethernet loopback free

The autonomy of the nodes means that any given device is free to transmit at any time, while the sharing of a common medium - originally a single coaxial cable - means that if two (or more) nodes decide to begin transmitting at the same time, those transmissions will collide. The context in which CSMA/CD operates is that of a fully distributed, packet-switched network consisting of autonomous nodes connected to a shared transmission medium (see Figure 1). The protocol which Metcalfe described in his memo is now known as Carrier Sense Multiple Access with Collision Detection, or CSMA/CD, after the title of the first IEEE 802.3 standard. Metcalfe delivers a memo to his employers in which he coins the term ‘ethernet’, and outlines the essentials of what will become the world’s pre-eminent local area networking technology.īob Metcalfe's 1973 sketch of his original 'Ethernet' vision. Meanwhile, at Xerox’s Palo Alto Research Centre (PARC) in California, a 27-year-old recent PhD graduate called Robert Metcalfe has been tasked with adding networking functionality to the company’s new Alto computer - the machine whose revolutionary graphical user interface would famously ‘inspire’ Steve Jobs.

In America, Skylab is launched, and Richard Nixon confesses to his role in the Watergate cover-up. In Britain, VAT and the Austin Allegro have recently been introduced. The home of Ethernet: Xerox’s Palo Alto Research Center.

So why has it taken so long for Ethernet to reach the recording studio, and what key benefits does it have to offer? To find the answers, we need to take a look at the development of Ethernet itself, and that means going back, back through the swirling mists of time. Yet, in principle, Ethernet has unique advantages over other formats, and it has already come to dominate the worlds of installation and high-end live sound. It wasn’t until 2011 - 26 years after the publication of the IEEE 802.3 standard - that the first DAW-focused Ethernet recording interfaces appeared. Until recently, however, the oldest and most ubiquitous connection format of all was absent from this list. Today, anyone wishing to add a high-quality, low-latency, multi-channel audio interface to a computer is spoiled for choice, with devices available in a whole host of formats: PCI, PCI Express, Cardbus, Expresscard, FireWire 400 and 800, USB Full-Speed, High-Speed and Super-Speed and Thunderbolt 1 and 2. We explain how it works - and why there are so many protocols! In other supported platforms, theĮthernet loopback test-mac command is optional to enable Ethernet loopback.Ī port cannot be configured as VLAN-aware and VLAN-unaware simultaneously, and the flow configuration must be either flow-aware or flow-unaware.Ĭommand is not supported on multiple ports (MIF) mode.įorm of the command disables the Ethernet loopback functionality on the specified port.The humble Ethernet cable: key to the future of digital audio?Īlready dominant elsewhere, audio over IP is poised to take over the studio world. To enable Ethernet loopback on these devices, you must first configure theĮthernet loopback test-mac command. TheĬommand is mandatory on Brocade ICX 7750, Brocade ICX 7450, and Brocade ICX 7250 devices. To enable Ethernet loopback on a port in the VLAN-unaware mode as flow-aware, theĮthernet loopback test-mac command must be executed before enabling the Ethernet loopback. The specified port does not need to be explicitly assigned as a member of any VLAN. The Ethernet loopback functionality on a port in the VLAN-unaware mode can be configured either as flow-aware or flow-unaware.